Marley Engineered Products HT1502SS Spécifications télécharger pdf

HTSS Series

Smart Series™ Wall Heater

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR

INJURY TO PERSONS:

1. READ ALL INSTRUCTIONS before installing or using the

heater.

2. ELECTRICAL SHOCK HAZARD: Disconnect all electrical

power coming to heater at circuit breaker box or main

disconnect switch and lock in OFF position before wiring.

All wiring must be in accordance with The National Electrical

Code and applicable local codes and ordinances.

The heater must be properly connected to an effective

building ground.

3. Verify the supply voltage coming to heater is the same as

shown on the heater nameplate before energizing.

Energizing at a voltage in excess of nameplate voltage will

damage heater and void warranty.

4. This heater has hot and arcing or sparking parts inside.

Do not install or use in areas where gasoline, paint, or flam-

mable liquids are used or stored.

5. Do not install this heater upside down, sideways, in ceiling,

or floor. Install only as shown in this manual. Refer to

Mounting Clearances, page 2 for minimum clearances that

must be maintained.

6. The heater assembly must be installed in the back box pro-

vided. Do not operate the heater without the grille installed.

7. This heater is not approved for use in corrosive

atmospheres such as marine, green house or chemical

storage areas.

8. Do not use outdoors.

9. Extreme caution is necessary when any heater is used by or

near children or invalids and whenever the heater is left

operating or unattended.

10. This heater is hot when in use. To avoid burns, do not let

bare skin touch hot surfaces. Keep combustible materials,

such as furniture, pillows, bedding, papers, clothes, and

curtains away from heater. Do not block air intakes or

exhaust in any manner. For efficient and safe operation, we

recommend keeping all items at least 3 feet from front of

heater.

11. Do not insert or allow foreign objects to enter any ventilation

or exhaust opening as this may cause an electric shock or

fire, or damage the heater.

12. Should the heater become blocked or otherwise overheat, it

is provided with a manual-reset thermal safety switch and

alarm light that will activate to alert that the heater has

cycled off. If warning light is on, check to see if the reason

for the overheating can be identified. Remove any

blockage, allow heater to cool, then press Reset button.

Heater should return to normal operation. Do not continue

to use heater if it repeatedly cycles off. Have it inspected

and repaired by a qualified repair person.

11. Use this heater only as described in this manual. Any other

use not recommended by the manufacturer may cause fire,

electric shock, or injury to persons.

SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS

WARNING

READ CAREFULLY - This manual provides instructions for the correct installation, safe use, and care of this product. Special

attention should be directed to the warnings provided below which identify certain precautions and special instructions for safe and

efficient installation and use. Studying these instructions first may save you considerable time and money later and keep your

installation time to a minimum. If you are not familiar with electricity or feel uncomfortable in working with electricity, refer the instal-

lation of this product to a licensed electrician or qualified person.

1 2 3 4 5 6

Résumé du contenu

Page 1 - HTSS Series

HTSS SeriesSmart Series™ Wall HeaterTO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK ORINJURY TO PERSONS:1. READ ALL INSTRUCTIONS before installing or using

Page 2 - INSTALLATION

SPECIFICATIONSUNPACKINGThe carton contains the following:• Remote control• Bottom bezel• Grille with installed electronics• Heater assembly• Installat

Page 3 - Wiring of Heater

3. Attach power supply ground wire to green ground pigtail leadusing appropriate Listed wire nuts or approved connectors.Push the wires into upper cor

Page 4 - OPERATION

3. If not already done, connect green (G) heater pigtail toequipment ground wire coming into heater.4. Push wires up into right hand corner of box out

Page 5 - REPAIR PARTS

MAINTENANCEYour heater is designed for years of trouble-free operation andrequires no special maintenance other than occasional cleaning.The motor is

Page 6 - LIMITED WARRANTY

03/10Part No. 5200-11046-000PPD11565LIMITED WARRANTYAll products manufactured by Marley Engineered Products are warranted against defects in workmansh